td1320 field tester of dc charger for electric vehicles -凯发k8国际

overview

td1320 is a portable instrument specially designed for on-site detection of dc charger. its dc voltage measurement is up to 1150 v, dc current measurement is up to 300 a (480 a optional), and dc power/electrical energy accuracy class is 0.02/0.05/0.1 optional. the instrument is suitable for on-site detection, conductive charging interoperability test and communication protocol conformance test of dc charger for metrology institute, electric power department and manufacturer.  

reference standard

● gb/t 18487.1-2015 electric vehicle conductive charging system—part 1：general requirements

● gb/t 20234.1-2015 connection set for conductive charging electric vehicles—part 1：general requirements

● gb/t 20234.3-2015 connection set for conductive charging electric vehicles—part 3：dc charging coupler

● gb/t 27930-2015 communication protocols between off-board conductive charger and battery management system for electric vehicle

● gb/t 34657.1-2017 interoperability test specifications of electric vehicle conductive charging—part 1：supply equipment

● gb/t 34658-2017 conformance test for communication protocols between off-board conductive charger and battery managements system for electric vehicle

● gb/t 29318-2012 electric energy metering for electric vehicle off-board charger

● jjg 1149–2018 verification regulation of off-board charger for electric vehicles

functions

● ripple measurement: it can detect ac ripple below 1 khz with wide dynamic range

● waveform display: real-time curve display and record of u (t), i (t), p (t), e (t).

● environmental temperature measurement: the temperature sensor is equipped to measure the site environmental temperature to correct the working error.

● clock verification: built in gps clock module, it can display real-time clock and synchronize with beijing time.

● built-in vehicle control and guidance circuit: it can complete the interoperability test of off-board charger, the adjustment range of r4 resistance simulation module is 400ω~ 5000ω, the step value of which is 1ω. each contact is provided with on-off switch, which can realize the simulation of the contact state.

● insulation resistance simulation: it can simulate the insulation state of charger. the input voltage range is 0v ~ 1000v, and the resistance adjustment range is 10 kω ~ 610 kω with the step of 5 kω, which is used to simulate the insulation fault of positive and negative poles.

features

● the broadband ac/dc current comparator technology is adopted, which is less affected by the thermal potential and has higher accuracy than the shunt.

● large current can be measured without wiring, and a single connection can automatically complete the preset test items.

● there are no mechanical contacts such as switches and relays in the current loop. it is not damaged for 5 seconds under overload of double rated current is with reliability is high.

● the current measurement loop achieves high isolation between the voltage circuit and the power supply, which can guarantee higher safety.

● the instrument can be calibrated with special calibration terminal.

● high-definition lcd touch screen is adopted, which has intuitive interface, convenient operation and is visible in sunlight.

● the instrument is equipped with can-bus, rs232, rs485, usb, wlan, wifi interface and host computer software to facilitate the establishment of automatic test system.

● portable instrument box with high level of anti-seismic and electrical protection is equipped, which is very convenient to carry to the scene.

test items

● calibration of charging energy metering characteristics: working error, charging amount display error, payment amount error, clock indication error, etc.

● conductive charging interoperability test: connection confirmation test, self-detection phase test, charging readiness test, charging phase test, normal charging end test, charging connection control sequence test, communication interruption test, switch s disconnection test, vehicle interface disconnection test, output voltage exceeding vehicle allowable value test, insulation fault test, other charging faults, output voltage control error test, output current control error test, output current control time test, output current stop rate test, control guidance voltage test, etc.

● communication protocol conformance test.

connection diagram of charger on-site detection

technical specifications

dc voltage

measurement characteristic：

● range switching: automatic or manual

● measurement range: 30 v～1150 v

● minimum resolution: 0.1 mv ( range of 300 v)，

● display: 7 digits

● accuracy of ripple measurement: ± 0.05%*rg, 

● bandwidth: ≤ 1 khz

dc current

measurement characteristic：

● range switching: automatic or manual

● measurement range: 0.5 a～300 a or 480a

● minimum resolution: 1 μa ( range of 5 a)，

● display: 7 digits

● accuracy of ripple measurement: ± 0.05%*rg

● bandwidth: ≤ 1 khz

dc electrical energy / power

● measuring range: combination of dc voltage range and dc current range

● accuracy: addition of dc voltage and dc current

● output of standard electrical energy pulse: the maximum frequency is 60 khz

   active and passive pulse is supported, and the load capacity is greater than 20 ma

   input of standard electrical energy pulse: the maximum frequency is 100 khz with the amplitude of 5v

● electrical energy measurement error: 7 digit decimal display

● clock accuracy: ± 0.1 ppm

general specifications

● line power: ac ( 198 v～253 v )，( 50 ± 2 ) hz；

● maximum power consumption: 80 va

● operating environment: -30 ℃～55 ℃，20%～80% r·h，non-condensing

● storage environment: -30 ℃～70 ℃，< 80% r·h，non-condensing

● dimensions（width*depth*height）: 560 mm × 460 mm × 260 mm

● weight: 28 kg

● standard interfaces: can-bus、rs232、rs485、usb、wlan、wifi

related products

selection guidance